Wooden Pendulum

Have you ever heard of a “pendulum“? It’s an instrument that is used by some people to locate ground water or to visualize invisible forces. Also it can look very pretty and make a decorative piece of jewelry or ornament. 🙂 I wanted to do a small woodworking project again, and as I needed a “magic present” for a spiritual friend, i decided to make a wooden pendulum. It worked out so well, that I made a couple more and did a tutorial for you guys. I hope you enjoy!

Wooden Pendulum

You’ll need:

thin, dry twigs (about the width of a finger)
sandpaper
a fine saw
a small eye screw (available here*)
a small rotary tool  (available here*)
woodburning tools (if you want do decorate your pendulum) (available here*)
waxed cotton cord (available here*)

 

How it’s done:

Pendulum Wood 01

1. You can use various types of wood for this project. Some believe that certain types of wood are better for special kind of tasks then others. If you want, you can choose the wood accordingly. I used mostly willow twigs. The important thing is, that your twigs should be as straight as possible and dry. Use twigs that are not too freshly cut.

Pendulum Wood 02

2. First thing I removed the bark with sandpaper. It works really well if you use one with a rougher one first and then move on to a fine one. If you make a couple of pendula a belt sander can come in handy. I secured an old one upside down on my work bench. Try to straighten out the twig as much as possible when you remove the bark.

Pendulum 01

A belt sander is faster but you are prone to make more mistakes.

Pendulum Wood 03

3.  Sharpen the twig roughly from four sides. It’s important that you stop to check every couple of seconds if all the sides are even.

Pendulum Wood 04

4. After that you smooth out the edges and try to round it as evenly as possible. It works best if you make rolling movement with your twig over the sandpaper. This step took me the longest of all. Often the tip will get wonky and you have to even it out again. You have to sacrifice a lot of your twig if you do that, so it’s better to start out with a longer one.

Pendulum 02

It’s especially hard with a belt sander, because small corrections are nearly impossible. If you apply a little to much pressure, half of your tip is gone. I cut out a lot of the video sequence. This step took about 4 minutes.

Pendulum Wood 05

5. If you are satisfied with the tip you can cut off the desired length for your pendulum. Use a fine saw to get a smooth cut.

Pendulum 03

 

Pendulum Wood 06

6. If you like the way it looks now, you could leave it at that. I wanted a rounded end on my pendulum, so I worked it with sandpaper again.

Pendulum 04

This is very hard to do with a belt sander, because the pendulum is too small to hold it securely. I sent more than one piece flying through the workshop. Rotate your pendulum carefully while you are sanding it.

Pendulum 05

Make a circular movement to achieve an evenly rounded end.

Pendulum Wood 07

7.  Those were my first finished bits. They reminded me a little of miniture vampire-hunting tools. 🙂

Pendulum Wood 08

8. You don’t have to decorate your pendulum if you don’t want to. A thin coating of varnish or beeswax will do. I used a woodburning tool (available here*) with a fine tip to draw small symbols and patterns on the wood.

Pendulum Wood 09

 9. It is easiest if you map out your pattern lightly. For this the tip of the woodburning tool should hardly touch the wood. (Or use a pencil.) It is possible to correct small mistakes at this point.

Tip: Use a sharp razor blade to take off thin portions of the wood if you made a mistake.

 

Pendulum Wood 10

10. Once you are satisfied, you can draw your pattern for real. Try to apply no pressure with the woodburning tool. It takes a bit of practice to get the hang of that.

 

Pendulum Wood 11

11. Now it’s time for little details (maybe some dots or shading) and corrections. The light in the pictures is a little bit too bright because I was sitting in the garden and direct sunlight. It was such a lovely day. I couldn’t stay inside! 🙂

I made a video of myself decorating one pendulum. The speed is increased. This took me about 8 minutes.

Pendulum Wood 12

12. This is a small selection of the pendula I made. I tried different patterns and techniques. You can see that some of the lines are not as dark as the others. That is because the woodburning tool was not hot enough. I corrected that later.

Pendulum Wood 13

13. You’ll need to be able to attach the pendulum to a string of some sort. So I drilled a little hole first. I used a rotary tool. (available here*)

Pendulum Wood 14

14. I wanted to be able to exchange the string later on, so I decided on an eye bolt. You can apply a drop of wood glue before you secure the bolt.

Pendulum 07

You don’t have to drill a hole, but it is easier to screw in the bolt later if you do.

Pendulum Wood 15

And that is the finished pendulum! 🙂 The string should be as long as your underarm. I like rustic decorations, so I made some wooden beads out of thin twigs. If you are interested, you can find the tutorial for that here. I also made the little goddess pendant myself. It’s made of polymer clay and can also be used as a pendulum. I will write a tutorial for that in the next couple of days.

 

 

And here is an overview of all the important steps to pin on pinterest! 🙂

 

*This blog post contains affiliate links. You can read all about them on my disclosure page. Link >>

One Reply to “Wooden Pendulum”

Leave a Reply

Your email address will not be published. Required fields are marked *